Prince's Wand Sizing & Ordering Info

D1 - Wand Length
D2 - Pin setback
D3 - Pin length
D4 - Front ball
D5 - Pin ball
D6 - Wand diameter
D7 - PA / Pin size
      -Taper Length
      -Ring size if required
--------------------


We Do Carry Sizing Kits To Help You Measure.
See Below



For Pinless Wands (Which does not require a piercing)
Such as:


For the Pinless Wands, we need measurements; D1, D2, D4, D6, and the Glans Ring size.

D2 Ring Setback for Pinless Wands only: Pinless Wands don’t have a P/A post, but we still need the measurement so that the Glans Ring will be located behind the Glans (head). Most cases it will be from 3/8” to 3/4”.




For Pinned Wands
Such as:



D1 Wand Length: 1” to 9”. We have found that a 3-1/2” is a good starter size for most. If the wand is over 4” there is an additional charge of $8.75 per 1/4".

D2 Pin Setback: This is the distance from your P/A piercing to the end of your urethra. In most cases it will be from 3/8” to 3/4”, but each one is different.

D3 Pin Length: For this you will have to put something in the urethra such as our Sizing Kit, and then take something else straight such as a straight barbell and put it through the P/A piercing until it touches the item that you inserted in your urethra, then measure that distance to get the length of the Pin. Most that we make are 1/8” to 3/8”, but there is no standard, each wand is different!

D4 Front ball: Depending on the wand size, I would recommend 7/16, 1/2, or 5/8. Ball sizes over 5/8 carry a small additional fee depending on the size, however we do have balls in stock up to 1-1/2” and can even set you up with several size options.

D5 Pinball: Most that I do are 3/8” but we can do most nay size, and can set you up with multiple sizes if you wanted. Over 5/8" does carry a small additional fee.

D6 Wand diameter: This is a tough one. If you are not a sounder, you may not have an idea of what size you want for your urethra. It is most commonly either 1/4", 5/16", or 3/8", but we can do most any size you want.
If you are unsure, we do carry a Stainless Steel sampler set for sizing that includes a 1/4”, 5/16”, and a 3/8”. Each has a rounded end for easy insertion, and this way you can get the correct sizes from the start. They also work well for help with measuring the D3 dimension if you do not know that. They are $27.99 per set and you can find them here Sizer Set. If the wand is an odd size or over 3/8” in diameter, there is a small extra charge.

D7 The pin size: This will be the pa size you have. We can make these from 10 gauge to 000 gauge.

Taper: If you would like your wand tapered that is no problem. If you would like just a Starter Taper of about 1" the charge is $17.50. If you would like a Taper over 1" the charge is $35.00. We recommend only a starter taper though on most, and No Taper at all if D6 is 5/16" or smaller.

Slave rings: Are available for both the D4 and/or the D5 balls and are an additional $26.00 each.

Glans ring: On the wand that also has a Glans ring, if you are unsure of the size, we also carry a sampler set of O rings for that sizing, which consists of nine O rings ranging in size from 3/4 to 1-7/16. The cost for the set is $17.99 and you can find that here Glans Sizer Set. You want the fit to be Not Tight, and also Not Loose, just snug While you are Hard.

This Form is to be used AFTER you have placed your order for which ever one of our wands that you decided on.
Click Here for Wands


Full Name:
Email Address:
D1 measurement:
D2 measurement:
D3 measurement:
D4 measurement:
D5 measurement:
D6 measurement:
D7 measurement:
Taper Length if needed:
Ring Size if needed: